Fluid Meters

Petroleum Basic Flow Meter

  • Flow ranges: 0.02 – 0.2 GPM (0.1 – 0.75 LPM) up to 20 – 300 GPM (100 – 1100 LPM)
  • Construction: Aluminum, brass and T303 stainless steel
  • Sizes: 1/4 to 3 inch ports
  • Ports: SAE, NPTF, BSPP, Code 61 and Code 62, 4-bolt flanged
  • Pressure up to 6,000 psi (414 bar) maximum
  • Temperature up to 240 °F (116 °C)
  • Accuracy ±2% full scale Repeatability ±1%
  • Standard calibration: .876 specific gravity, 140 SUS (32 cSt) hydraulic oil
  • Direct reading
  • Install in any position
  • 360° rotatable guard/scale
  • Easier to read linear scale
  • No flow straighteners or special piping required
  • Relatively insensitive to shock and vibration
  • Good viscosity stability (40 to 500 SUS / 4.2 to 108 cSt)
  • Optional: – Special scales available – Reverse flow by-pass

Petroleum Test Kit

  • Flow ranges: 0.1 – 1.0 GPM (0.5 – 3.75 LPM) up to 10 – 150 GPM (50 to 560 LPM)
  • Construction: Aluminum, brass and T303 stainless steel
  • Sizes: 1/4 to 1-1/2 inch ports
  • Ports: NPTF and BSPP
  • Pressure up to 6000 psi (414 bar) maximum
  • Temperature up to 240 °F (116 °C)
  • Accuracy ±2% full scale
  • Repeatability ±1%
  • Standard calibration: .876 specific gravity, 140 SUS (32 cSt) hydraulic oil
  • Direct reading
  • Install in any position
  • 360° rotatable guard/scale
  • Easier to read linear scale
  • Good viscosity stability (40 to 500 SUS / 4.2 to 108 cSt)
  • No flow straighteners or special piping required
  • Valve: – 1/2, 3/4 and 1 inch series – needle valve
  • Pressure gauge, glycerin dampened: 0 – 3500 psi (0 – 240 bar) for aluminum & brass meters 0 – 6000 psi (0 – 400 bar) for stainless steel meters
  • Includes: – Basic flow meter – Control valve – Pressure gauge
  • Optional: – Special scales available – Reverse flow by-pass

Petroleum High Temperature Meter

  • Flow ranges: 0.1 – 1.0 GPM (0.5 – 3.75 LPM) up to 10 – 150 GPM (50 – 560 LPM)
  • Construction: Aluminum, brass and T303 stainless steel
  • Sizes: 1/4 to 1-1/2 inch ports
  • Ports: SAE, NPTF and BSPP
  • Pressure up to 6,000 psi (414 bar) maximum
  • Temperature up to 500 °F (260 °C)
  • Accuracy ±2% full scale
  • Repeatability ±1%
  • Standard calibration: .876 specific gravity, 140 SUS (32 cSt) hydraulic oil
  • Direct reading
  • Install in any position
  • 360° rotatable guard/scale
  • Easier to read linear scale
  • No flow straighteners or special piping required
  • Relatively insensitive to shock and vibration
  • Good viscosity stability (40 to 500 SUS / 4.2 to 108 cSt)
  • Optional: – Special scales available – Reverse flow by-pass

Petroleum Flow-Alert Micro Switch

  • Automatically signals alarm if flow is too high or too low
  • Automatically opens or closes electrical circuits
  • Triggers warning lights, buzzers and other devices
  • Shuts down pumps and/or other equipment to protect your operation against permanent damage
  • Flow ranges: 0.02 – 0.2 (0.1 – 0.75 LPM) up to 10 – 150 GPM (50 – 560 LPM)
  • Construction: Aluminum, brass and T303 stainless steel
  • Sizes: 1/4 to 1-1/2 inch ports
  • Ports: SAE, NPTF and BSPP
  • Pressure up to 6,000 psi (414 bar) maximum
  • Temperature up to 240 °F (116 °C)
  • Accuracy ±2% full scale
  • Repeatability ±1%
  • Standard calibration: .876 specific gravity
  • Install in any position
  • Easier to read linear scale
  • No flow straighteners or special piping required
  • Relatively insensitive to shock and vibration
  • Good viscosity stability
  • Housing: Anodized and epoxy-coated aluminum with polycarbonate lens
  • Rating: NEMA 12 and 13(IP52/54)
  • Micro Switch: Single(1) or Double(2) prewired single-pole, double-throw (SPDT)
  • Connection: Pig-tail conductor (standard) with water-tight strain relief
  • Includes: Basic flow meter with Flow-Alert flow switch
  • Optional: Special scales available

Phosphate Basic Flow Meter

  • Flow ranges: 0.02 – 0.2 GPM (0.1 – 0.75 LPM) up to 10 – 150 GPM (50 – 560 LPM)
  • Construction: Aluminum, brass and T303 stainless steel
  • Sizes: 1/4 to 1-1/2 inch ports
  • Ports: SAE, NPTF, BSPP, Code 62, 4-bolt flanged
  • Pressure up to 6,000 psi (414 bar) maximum
  • Temperature up to 240 °F (116 °C)
  • Accuracy ±2% full scale
  • Repeatability ±1%
  • Standard calibration: 1.18 specific gravity, 140 SUS (32 cSt) hydraulic oil
  • Direct reading
  • Install in any position
  • 360° rotatable guard/scale
  • Easier to read linear scale
  • No flow straighteners or special piping required
  • Relatively insensitive to shock and vibration
  • Good viscosity stability (40 to 500 SUS / 4.2 to 108 cSt) Consult factory for other viscosities
  • Optional:
    – Special scales available
    – Reverse flow by-pass

Phosphate Flow-Alert Reed Switch

  • No mechanical linkage
  • Provides output to signal alarm if flow is too high or too low
  • Flow ranges: 0.02 – 0.2 GPM (0.1 – 0.75 LPM) up to 10 – 150 GPM (50 – 560 LPM)
  • Construction: Aluminum, brass and T303 stainless steel
  • Sizes: 1/4 to 1-1/2 inch ports
  • Ports: SAE, NPTF, and BSPP
  • Pressure up to 6,000 psi (414 bar) maximum
  • Temperature up to 240 °F (116 °C)
  • Accuracy ±2% full scale
  • Repeatability ±1%
  • Standard calibration: 1.18 specific gravity
  • Install in any position
  • Easier to read linear scale
  • No flow straighteners or special piping required
  • Relatively insensitive to shock and vibration
  • Good viscosity stability
  • Housing: Anodized and epoxy-coated aluminum with polycarbonate lens
  • Rating: NEMA 12 and 13 (IP52/54)
  • Reed Switch: Single(1) or Double(2) prewired single-pole, single-throw (SPST-NO) normally open or single-pole, single-throw (SPST-NC) normally closed
  • Connection: 4 pin (Protection Class IP65)
  • Includes: Basic flow meter with Flow-Alert flow switches
  • Optional: Special scales available

MR Flow Transmitter

  • Operate as part of a totally integrated electronic process control/data acquisition system
  • Digital flow rate and total flow indication
  • Proportional analog outputs for electronic integration
  • Non-contact sensor electronics
  • In-field compensation for specific gravity and viscosity
  • Flow ranges: 0.1 – 1.0 GPM (0.5 – 3.75 LPM) up to 10 – 150 GPM (50 – 560 LPM)
  • Construction: Aluminum, brass and T303 stainless steel
  • Sizes: 1/4 to 1-1/2 inch ports
  • Ports: SAE, NPTF and BSPP
  • Pressure up to 6,000 psi (414 bar) maximum
  • Temperature up to 240 °F (116 °C)
  • Accuracy ±2% full scale
  • Repeatability ±1%
  • Standard calibration: 1.18 specific gravity
  • Install in any position
  • No flow straighteners or special piping required
  • Insensitive to shock and vibration
  • Good viscosity stability
  • Housing: Anodized and epoxy-coated aluminum with polycarbonate lens
  • Rating: NEMA 12 and 13 (IP 52/54)
  • Connection: 4-pin
  • Electrical: 10-30 Vdc power supply or loop-powered on 4-20 mA current
  • Outputs: Factory calibrated, field selectable 4-20 mA, 0-5 Vdc and 0-10 Vdc
  • CE compliant — exceeds US and meets European standards for EMI/EMC
  • US Patent 7,130,750
  • Includes: Basic flow meter with flow transmitter output

Water-based Fluid Meters

  • Flow ranges: 0.02 – 0.2 GPM (0.1 – 0.75 LPM) up to 20 – 300 GPM (100 – 1100 LPM)
  • Construction: Aluminum, brass and T303 stainless steel
  • Sizes: 1/4 to 3 inch ports
  • Ports: SAE, NPTF, BSPP, Code 61 and Code 62, 4-bolt flanged
  • Pressure up to 6,000 psi (414 bar) maximum
  • Temperature up to 240 °F (116 °C)
  • Accuracy ±2% full scale
  • Repeatability ±1%
  • Standard calibration: 1.0 specific gravity for water-based emulsions
  • Direct reading
  • Install in any position
  • 360° rotatable guard/scale
  • Easier to read linear scale
  • No flow straighteners or special piping required
  • Relatively insensitive to shock and vibration
  • Good viscosity stability (40 to 500 SUS / 4.2 to 108 cSt)
  • Consult factory for other viscosities
  • Optional:
  • – Special scales available
  • – Reverse flow by-pass

Air and Compressed Gas Meters

  • Flow ranges: 0.5 – 5.0 SCFM (0.2 – 2.2 L/SEC)
  • up to 200 – 2200 SCFM (75 – 1130 L/SEC)
  • Construction: Aluminum, brass and T303 stainless steel
  • Sizes: 1/4 to 3 inch ports
  • Ports: SAE, NPTF and BSPP
  • Pressure up to 1,000 psi (69 bar) maximum
  • Temperature up to 240 °F (116 °C)
  • Accuracy ±2% full scale
  • Repeatability ±1%
  • Standard calibration: 1.0 specific gravity
  • Direct reading
  • Install in any position
  • 360° rotatable guard/scale
  • Easier to read linear scale
  • No flow straighteners or special piping required
  • Relatively insensitive to shock and vibration
  • Optional:
    – Special scales available
    – EP option, extended inlet cap with plugged pressure gauge port
    – EG option, extended inlet cap with pressure gauge installed